Ghost Controls Hinge & Roller Replacement Nationwide

Ghost Controls Hinge & Roller Replacement: The Woodland Hills Owner’s Guide

Ghost Controls hinge and roller replacement in Woodland Hills typically runs $220 to $480 installed, and we usually have the right parts on the truck. Most homeowners discover the failure the same way: the gate starts dragging on the ground, squeals when it moves, or the opener struggles and trips its force setting because the hinge or roller has finally worn out. The part itself looks simple, but matching it to your specific Ghost Controls arm and gate weight is where the job gets done right or wrong.

Call (650) 719-7207

• What you’ll get: correct part match, written price, install, and a 365-day written guarantee.
• Most common cause: metal fatigue at the pivot point, accelerated by Woodland Hills heat and dry-season dust.
• What it costs: $220-$480 depending on hinge vs. roller, post condition, and gate weight.

Which Ghost Controls Models This Applies To

Ghost Controls swing gate arms, from the single-arm AX1D and dual-arm AX2D through the heavier TSS1 and TDS2 series, all hinge on a pivot bracket and move through a roller or glide track depending on how your Woodland Hills gate was set up. The hinge on a Ghost arm is not a generic gate hinge. It’s the pivot where the articulating arm meets the post bracket, and its pin diameter and bracket footprint vary between the residential AX line and the stouter TSS line.

Here’s the gotcha we see in Woodland Hills: a homeowner buys a universal hinge kit online, bolts it on, and the arm now sits 3/8-inch off its original arc. That small shift forces the operator to work harder to open and close, and three months later the gear inside the arm fails. On a Ghost Controls arm, matching the hinge exactly matters. We stock OEM Ghost Controls hinges and rollers, plus quality aftermarket equivalents where they meet the same spec. If you want to identify the part before you call, look for the model tag on the arm body, and measure the hinge pin diameter in millimeters: AX parts use a 3/8-inch pin, TSS and TDS parts run a 1/2-inch pin. Tell us the measurement and the model, and we’ll tell you if it’s in the van.

One more compatibility note: Carver Gate Repair Woodland Hills is an independent service provider, not affiliated with Ghost Controls. We work on their equipment every week, and we stock parts for LiftMaster, Mighty Mule, and DoorKing too, but Ghost is the brand we see most often in Woodland Hills residential swings.

Signs Your Ghost Controls Hinge & Roller Replacement Is Failing

• The gate drops when the opener releases. The hinge pin has worn oval or the bracket has shifted on the post. The arm is no longer holding the gate at its original height, and every cycle is grinding metal against metal.
• A screech or groan on every open and close. The roller has gone dry, gotten pitted from dust, or the hinge pin is binding. The noise happens at the same point in the travel every time. Lubricating quiets it for a day, then it comes back.
• The opener stalls and reverses. The increased drag from a failing hinge or roller forces the Ghost arm’s internal clutch to slip, and the gate looks like it hits an invisible stop. The arm is fine. The pivot underneath it is not.
• Visible play at the pivot point. If you can wiggle the arm side to side while the gate is in place, the hinge is done. Any play wider than a millimeter at the pin means the arm is hammering the bracket with every cycle and wearing both out fast.
• Rust streaks running down the bracket. The hinge has worn through its coating and the base metal is exposed to Woodland Hills morning fog and afternoon sun. Rust line, then pitting, then a snapped pin.

Replacement Cost & What’s Included

In Woodland Hills, a Ghost Controls hinge replacement installed runs $220 to $340 for a standard AX-series arm. A roller replacement typically lands at $240 to $380. TSS and TDS heavy-series parts run higher, $340 to $480, because the parts are beefier and the post bracket often needs a plate or reinforcement.

Every quote is written before any work starts, and the number you sign off on is the number on the invoice. The price includes the part, the labor to pull the arm safely, the alignment, and a full cycle test. Every repair carries a written 365-Day Done Right Promise. If the hinge or roller we install fails inside a year, we come back and make it right, no charge.

DIY or Call Us?

A homeowner can safely identify the symptom, measure the pin diameter, and even photograph the model tag for us. That’s useful, and it saves time when we arrive. What we don’t recommend is unbolting a Ghost arm while the gate is under its own weight. The hinge pin is under load, the arm is pressing against the gate, and if you pull the wrong bolt first, that gate swings free or drops hard. We’ve repaired more than one bent gate panel in Woodland Hills after a well-intentioned Saturday project went sideways.

If you want to know exactly what’s wrong before spending a dollar, call (650) 719-7207. We’ll talk through what you’re seeing, tell you honestly if it sounds like the hinge, the roller, or something else, and give you a written price before any work begins. Lonnie Burke and the crew know Ghost arms well enough to diagnose most failures over the phone in five minutes.

FAQs

Call Carver Gate Repair Woodland Hills

If your Ghost Controls gate is dragging, squealing, or the opener keeps hitting its force limit, don’t wait until the hinge pin snaps and drops the gate on the driveway. Call (650) 719-7207 for a free estimate. A real person answers, day or night. We’ll get a background-checked, uniformed technician to your Woodland Hills home with the right Ghost Controls part, a written price, and a one-year guarantee in writing. We fix it right the first time, or we come back and fix it right.

Written by Lonnie Burke, Owner, Carver Gate Repair Woodland Hills at Carver Gate Repair Woodland Hills, serving Woodland Hills and nearby areas.