A Carver company - serving Woodland Hills, CA

Before & After Gallery - Carver Gate Repair Woodland Hills

Wood & steel frameWood & steel frame
Wrought ironWrought iron
Farm & ranchFarm & ranch
Sliding driveway gatesSliding driveway gates
LiftMaster operatorsLiftMaster operators
Every visit starts with

Free on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted

The assessment is free and the quote is the invoice.

Get your free estimate

Gate Repair Before & After in Woodland Hills, CA

Photos tell the truth faster than any claim we could make. Below are real gate repair scenarios we handle across Woodland Hills, from Warner Center to the hills above Ventura Boulevard. Each one shows the problem as we found it, the fix we made, and how the gate works now. Gates that open and close every time. That’s the whole job.

Call (650) 719-7207

Explore

Styles & brands we work with

Wrought iron
Wrought iron
Wood & steel frame
Wood & steel frame
Farm & ranch
Farm & ranch
Sliding driveway gates
Sliding driveway gates
LiftMaster operators
LiftMaster operators

Recent Transformations

Sliding Gate Motor Replacement in Walnut Acres

Before & After: Sliding gate motor replacement, Walnut Acres area

The old motor had been failing for months. Homeowners told us they’d been lifting the gate manually just to get the car out. We pulled the dead operator, traced the wiring, and found the limit switch had worn past adjustment. Installed a new LiftMaster slide operator matched to the gate’s weight, reset the travel limits, and replaced the safety photo eyes. The gate now opens in about six seconds and stops exactly where it should, every single cycle.

Broken Swing Gate Hinge in the Woodland Hills Hillsides

Before & After: Wrought-iron swing gate re-hung on new hinges

A heavy wrought-iron gate had sagged so badly it dragged across the driveway with every swing. Both lower hinges had egged out from years of wind load coming up the canyon. We lifted the gate, cut out the old hinge pins, and re-hung it on new ball-bearing hinges sized for the actual gate weight. Before we touched the operator, we made sure the gate itself swung true. You can push it with one hand now. Then we re-set the opener’s close limits and it’s been quiet ever since.

Gate Motor Repair on a Slope-Side Property off Mulholland

Before & After: FAAC swing operator repair, hillside driveway

This one’s a good example of a gate that wasn’t dead, just dying. The FAAC articulating arm operator would open fine but stall on the closing stroke, especially on hot afternoons. We checked the capacitor first, then tested the motor windings under load. The cap was out of spec and the arm’s pivot joints were bone dry. Replaced the capacitor, lubricated the arm pivots with the right grease, and re-torqued every mount bolt. The operator’s been closing against this slope for months now without a hitch.

Loop Detector Replacement for a Condo Entry on Topanga Canyon

Before & After: Loop detector replacement, Topanga Canyon condo entry

Residents were pressing the call button because the gate wouldn’t open when a car pulled up. The loop detector, which senses a vehicle sitting over the sawcut in the concrete, had failed completely. We cut in a new loop, ran the lead-in wire through fresh conduit, and installed a new detector module matched to the existing DoorKing board. The gate now opens automatically for every car that pulls up, and the free-exit loop works the same. Nobody’s buzzing the manager anymore.

Safety Photo Eyes Restored on a Gated Courtyard Near Ventura Boulevard

Before & After: Safety photo eyes retored and aligned, gated courtyard entrance

This gate would slam and reverse halfway through its travel, every third or fourth cycle. The photo eyes, which keep the gate from closing on a person or car, had drifted out of alignment and one lens was sun-fogged. We mounted the receiver and sender on rigid plates so they stay put, replaced the clouded lens, and re-checked the beam alignment with a meter. Gate closes smoothly now and stops instantly if anything breaks the beam. That’s the part of the job nobody sees until it saves someone.

Full Gate Installation on a New Build off Valley Circle

Before & After: New driveway gate installation, Valley Circle area

The homeowners had a bare driveway and a rough idea. We measured the opening, matched a custom steel gate to their home’s exterior, and installed it with a Ghost Controls swing operator wired on a dedicated circuit. Added a keypad, a keyed bypass for the fire department, and both radio remotes. The gate’s been in since early spring and it’s still the same smooth, quiet open it was the day we finished.

Want Results Like These?

If your gate is grinding, sagging, stalling, or just refusing to move, we’ll come out, diagnose it, and hand you a written price before any work starts. That price doesn’t move at the door. Call Carver Gate Repair Woodland Hills at (650) 719-7207 and we’ll get a technician to your driveway. Every repair carries a written guarantee, good for a full year.

Written by Lonnie Burke, Owner at Carver Gate Repair Woodland Hills, serving Woodland Hills since 2008.

Before & after

See the difference

Before - Recent ProjectBeforeAfter - Recent ProjectAfter
Recent Project
Before - Full RestorationBeforeAfter - Full RestorationAfter
Full Restoration
Before - Complete UpgradeBeforeAfter - Complete UpgradeAfter
Complete Upgrade
Need Gate Repair help in Woodland Hills? Licensed & insured · 60-minute response · free estimates
Call (650) 719-7207
Local Service Coverage

Request a Free Estimate in Woodland Hills

Tell us what you need - Carver Gate Repair Woodland Hills responds fast. No obligation.

By submitting this form, you accept our Privacy Policy and consent to being contacted through phone, text, or email concerning your request, including by the partner businesses that may perform the service.

Prefer to text? Text Now
Call Now - 24/7 Dispatch