Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterWeld & Rust Repair in Woodland Hills, CA
Weld and rust repair in Woodland Hills typically costs between $200 and $750 per gate, depending on how far the corrosion has spread and whether structural steel needs to be replaced outright. Most weld repairs on residential driveway and pedestrian gates in the area are completed the same day the technician arrives. At Carver Gate Repair Woodland Hills, we handle everything from cracked hinge welds to full bottom-rail replacement, and every job gets a written price before we pick up a grinder. We also offer Automatic Gate Repair for gates with operators. That’s how we’ve operated under The Garrison Standard since 2008, and it’s the same standard we apply to every weld and rust job in the 91364 and 91367 zip codes.
Woodland Hills sits at the western edge of the San Fernando Valley, and the combination of summer heat, overnight marine-layer moisture, and occasional Santa Ana-driven dust takes a real toll on steel gates. Paint fails first. Then surface rust sets in. Then the rust works its way into hinge barrels, latch housings, and the bottom rail where water pools. Gate welding is not a side job for a general handyman. If you want the repair to hold up through next year’s heat, the steel needs proper prep, the weld needs proper penetration, and the finish needs proper sealing. We do all three, and we put it in writing. Call (650) 719-7207 and we’ll send a technician who has done this exact work on gates throughout Woodland Hills, from Walnut Acres to the neighborhoods south of Ventura Boulevard.
For a broader look at how we handle full gate systems, motors, and hardware, start with our Gate Repair in Woodland Hills page. This page covers the specific discipline of welding and rust remediation.
When You Need Weld & Rust Repair
Rust on a gate is rarely just cosmetic. Once moisture breaches the paint or powder coat, the steel underneath loses material every year it goes untreated. Here are the situations we see most often when Woodland Hills homeowners call us for weld and rust work:
- The gate sags and scrapes the driveway. This usually means the bottom hinge weld has cracked or the hinge leaves have pulled away from the post. Tightening bolts won’t fix it. The hinge needs to be cut off, cleaned, and re-welded in a corrected position.
- The bottom rail is rotted through. Water pools inside the bottom horizontal rail because most gates have no weep holes, or the existing weep holes are clogged with dust. We cut out the rotted section, weld in new steel of the same gauge, and drill proper drainage so the same thing doesn’t happen again in two years.
- The latch or lock housing has rusted loose. On many Woodland Hills properties, the gate gets heavy daily use. A rusted latch post or striker plate eventually breaks free at the weld. We repair the mounting surface and re-secure the hardware so the gate actually locks again.
- Surface rust is spreading along welds and joints. This is the early stage, and it’s the cheapest time to act. We grind the affected areas down to bare metal, treat the surface, and refinish before the rust reaches structural steel.
- A weld has cracked after a previous repair failed. If a previous welder laid a cold weld or failed to bevel the joint, the crack comes back. We inspect the entire weld line and redo it properly, not just the visible break.
- The gate post itself is rusting at ground level. This is the most serious scenario. Posts rust from the inside out where they enter the concrete footing. We assess whether the post can be reinforced with a welded sleeve or needs full replacement.
If any of these sound familiar, call us at (650) 719-7207. We’ll ask a few questions about your gate over the phone and give you a straight answer on whether a technician should look at it in person.
Our Weld & Rust Repair Process
You don’t need to know how to weld to understand what we’re doing to your gate. Here is the process we follow on every weld and rust job, step by step, so you know exactly what to expect when the technician arrives:
- Inspection and written price. The technician examines the gate, identifies every rust-damaged and weld-failed area, and writes down what the job requires. You get a fixed price before any work starts. The price does not move at the door. This is a non-negotiable part of The Garrison Standard.
- Surface preparation. We remove the damaged material. That means grinding off rust, cutting out rotted sections, and beveling the edges of any steel we’re about to join. If the metal isn’t prepared correctly, the weld will fail. This step takes time, and we don’t rush it.
- Welding and structural repair. We weld the prepared joints using the correct process for the steel thickness and gate type – MIG for most residential gates, TIG where precision matters on thin ornamental work. We replace rotted sections with matching steel, not whatever scrap happens to be on the truck.
- Rust treatment and sealing. Every remaining surface gets treated for corrosion. We apply a rust-inhibiting primer to welded and ground areas, then match the finish as closely as possible to the existing gate color. On heavily corroded gates, we’ll recommend a full repaint so the repair doesn’t stand out.
- Hardware check and realignment. After welding, we re-hang the gate, set the hinges, and confirm the gate swings true and latches cleanly. If the gate has an opener, we check that it operates without strain after the repair.
- Cleanup and written guarantee. We remove grinding dust, weld spatter, and cutoff scraps. You get a written guarantee on the repair, good for a full year. If the repair fails inside that year, we come back and fix it free. No charge, no argument.
Weld & Rust Repair Pricing in Woodland Hills
Here are the price ranges we quote on weld and rust work in the Woodland Hills area. These are honest ranges for typical residential gates, not estimates that grow once the job is open. Your written quote depends on the gate size, the amount of damaged steel, and whether the gate needs repainting after the repair:
| Repair Type | Typical Price Range |
|---|---|
| Surface rust treatment on a 4-foot pedestrian gate | $200 – $350 |
| Rust treatment on a double driveway gate (12-16 feet wide) | $400 – $750 |
| Single hinge re-weld | $180 – $300 |
| Bottom rail section replacement | $350 – $600 |
| Latch or lock housing repair and re-weld | $200 – $400 |
| Gate post reinforcement with welded sleeve | $450 – $800 |
| Full gate restoration (rust removal, welding, priming, repaint) | $800 – $1,500+ |
What moves the price on your gate? The biggest factor is how far the rust has spread before you call. A gate with light surface rust costs less to fix than a gate with rusted-through bottom rails. Gate size matters too. A 16-foot driveway gate has more steel, more weld joints, and more surface area than a 4-foot pedestrian gate. Post damage adds cost because it involves excavation or reinforcement work around the footing. And if the finish needs full repainting rather than spot treatment, that’s additional labor and material.
If the repair is straightforward, the price we quote over the phone after our inspection will fall within the ranges above. You’ll know the number before any work starts. That’s how we’ve done it since 2008, and it’s the same Garrison Standard applied to our work on Gate Repair across every brand we service, including LiftMaster, FAAC, and Elite openers that often hang on welded steel gates. Estimates are free. Call (650) 719-7207 to schedule an inspection.
FAQs – Weld & Rust Repair
How much does it cost to repair a rusted gate in Woodland Hills?
Rusted gate repair in Woodland Hills typically costs between $200 and $750 for most residential gates, depending on whether the rust is surface-level or has eaten through structural steel. Full gate restoration with repainting can run $800 to $1,500 or more. Call (650) 719-7207 and we’ll give you a written price after a technician inspects the gate. Estimates are free.
Can you repair my rusted gate the same day?
Yes, in most cases we can complete weld and rust repair the same day we inspect the gate, as long as the damage doesn’t require full gate removal or extensive repainting. Most hinge re-welds and bottom rail replacements are done in a single visit. Call (650) 719-7207 in the morning and we’ll get a technician scheduled.
Is it cheaper to repair a rusted gate or replace it?
Repair is almost always cheaper than replacement when the gate frame is still structurally sound. A typical weld and rust repair runs $200 to $750, while a new custom driveway gate in Woodland Hills starts around $1,500 for a basic steel gate and climbs from there. We’ll tell you straight if your gate is too far gone to justify repair, and we won’t weld a gate that should be replaced. Call (650) 719-7207 for an honest assessment.
Do you work on the gate motor after a weld repair?
Yes. After we re-hang a welded gate and set the hinges, we check that the gate operator runs without strain and perform Gate Realignment as needed. Our technicians are trained on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, so if the motor needs adjustment or the limit switches need to be re-set after the gate’s weight or alignment changed, we handle that on the same visit. Call (650) 719-7207 and we’ll cover both the steel and the motor.
Does your weld repair come with any kind of guarantee?
Every weld and rust repair comes with a written guarantee, good for a full year from the date of service. If the repair fails inside that guarantee window, you get a free second visit. No charge, no argument. That’s the 365-Day Done Right Promise, and it’s been the standard at Carver Gate Repair since 2008. Call (650) 719-7207 and we’ll put it in writing.
If you’re in Woodland Hills and your gate is rusting through, sagging, or swinging on a cracked weld, call us at (650) 719-7207 for a free estimate. We also specialize in Electric Gate Repair for powered systems. A background-checked, uniformed technician will inspect the gate, hand you a written price, and handle the repair on the spot if it’s a same-day job. The gate keeps your property secure, and the repair should hold up. We put that promise in writing, every time.
Written by Lonnie Burke, Owner at Carver Gate Repair Woodland Hills, serving Woodland Hills.