Ghost Controls Gate Repair Nationwide

Ghost Controls Gate Repair in Woodland Hills: What to Know First

We repair Ghost Controls gate operators across Woodland Hills, from the older AXDP and GTO/PRO swing series to current RGD and TSS1 slide systems, and we typically diagnose the problem the same day we arrive. Most Ghost Controls repairs run $180 to $420 for parts and labor, with motor or control board replacement on the higher end, and you’ll get a written price before we touch anything. If you’re in Woodland Hills and your Ghost Controls gate is dead, grinding, or halfway open, call (650) 719-7207 and we’ll get a technician out.

Call (650) 719-7207

How Ghost Controls Products Fail – and How We Fix Them

• AXDP and AXDPII swing operators losing travel limits. On older Woodland Hills installs, the limit switch assembly inside the actuator housing wears down and the gate starts slamming past its normal stop, or stops short and reverses. Ghost Controls built these early units with plastic limit cams that crack after enough heat cycles. We replace the cam set, recalibrate travel, and test for full obstruction reversal before we leave. If the board is also scorched, we’ll tell you before replacing it.
• GTO/PRO series failing to respond to remotes after a power blink. The receiver board on GTO/PRO units is sensitive to voltage spikes, and Woodland Hills gets its share of DWP grid blips during summer heat waves and Santa Ana wind events. You’ll see the gate open fine from the push button but not from the remote. We check the receiver first, not the remote, then reprogram and harden the connection if the board is still good. If the receiver is shot, we can install an aftermarket receiver that works with your existing remotes, no need to replace the whole operator.
• RGD slide operators with a gate that travels but won’t fully close. This is the most common Ghost Controls slide failure we see on gated driveways in the Warner Center corridor and along the larger lots south of Ventura Boulevard. The internal gear rack or the drive gear has picked up enough wear that the gate loses position as it moves, and the controller thinks it’s further along than it is. We inspect the gear, rack, and chain before condemning the motor, because Ghost Controls slide operators often need re-tensioning and a limit reset, not a full replacement.
• TSS1 solar units eating batteries faster than they should. These are popular on Woodland Hills properties where running line voltage to the gate is impractical, but the solar charge controller on older TSS1 boards drifts and overcharges or undercharges the battery. The symptom is a gate that works in the afternoon and dies by morning. We test the panel output, replace the charge controller if needed, and move the battery to a marine AGM that handles heat better than the stock sealed unit. We don’t put a new battery on a bad charge controller; that just wastes your money twice.
• Ghost Controls arm brackets pulling loose from the gate post. On swing gates, Ghost Controls sells a bolt-through mounting kit, but many installs we see in Woodland Hills used lag bolts into soft or cracked gate posts. The operator works fine, but the arm tears out of the post or the whole post starts leaning. We reset the post, through-bolt the bracket, and re-square the gate before recalibrating. The operator is rarely the problem in these cases; the mounting is.

Our Ghost Controls Gate Repair Process

1. 1
   You call (650) 719-7207, a live person answers. We ask what the gate is doing, when it started, and what Ghost Controls model you have if you know it. That helps our technician bring the right parts on the first trip instead of guessing.
2. 2
   The technician shows up on time and starts by inspecting the full system. We check the operator, the arm, the limit switches, the battery or power supply, the photo eyes, and the gate itself. Half of our Ghost Controls repairs in Woodland Hills turn out to be a mechanical or power problem the operator is being blamed for.
3. 3
   You get a written diagnosis and a firm price. We write down exactly what we found, what we recommend, and what it will cost. That number doesn’t move because we found something else later, and you can say no up front with no charge beyond the service call.
4. 4
   We repair the Ghost Controls equipment or replace it if necessary. When OEM parts are available and make sense for the unit, we use them. When a unit is discontinued and OEM isn’t available, we use quality aftermarket parts rated for the same load and environment, and we tell you which it is before we buy anything.
5. 5
   We test the gate through multiple cycles, check all safety reverses, and clean up. We don’t leave wire clippings, old parts, or oil spots. Your gate should work the way Ghost Controls intended when it was installed.
6. 6
   We give you a written guarantee on the repair, good for a full year. If the same issue returns inside that year, we come back and fix it at no charge. That’s the Garrison Standard, and we don’t do exceptions on it.

What Ghost Controls Gate Repair Costs in Woodland Hills

Here’s what Ghost Controls repair work typically runs in Woodland Hills:

• Service call and diagnosis: $89 to $129, waived if you approve the repair
• Limit switch replacement (AXDP, GTO/PRO): $180 to $260
• Receiver board replacement: $140 to $230
• Drive gear or rack repair (RGD slide): $220 to $380
• Solar charge controller replacement (TSS1): $160 to $250
• Full operator replacement (parts and labor): $700 to $1,200, depending on model and gate size

Price drivers are the age of the unit, whether OEM parts are still manufactured, and how much of the mechanical side needs work. A simple limit switch replacement on an AXDP is quick. An RGD slide operator with a wasted gear and a binding gate is a longer job. The one thing that doesn’t change is that you’ll see the full price in writing before we start. Call (650) 719-7207 and we’ll give you an honest range for what your gate needs.

Why Woodland Hills Homeowners Call Carver Gate Repair Woodland Hills for Ghost Controls Work

We fix Ghost Controls equipment every week, which means our technician rarely sees a failure we haven’t already solved a dozen times. We know which Ghost Controls models are worth repairing and which ones are past their service life, and we’ll tell you straight which side your gate is on. We also work on LiftMaster, Mighty Mule, DoorKing, and the other big brands, so if your gate has a mixed setup or you’re replacing a Ghost Controls unit with something more common, we can handle the conversion without bringing in another contractor. Every technician we send to Woodland Hills is background-checked and in uniform, and every repair carries our 365-Day Done Right Promise in writing. That’s how Lonnie Burke runs this shop, and that’s how it stays.

FAQs