FAAC Hinge & Roller Replacement Nationwide

FAAC Hinge & Roller Replacement: The Woodland Hills Owner’s Guide

FAAC hinge and roller replacement in Woodland Hills typically runs $240 to $480 installed, depending on which FAAC series your gate uses and how many points need swapping. We carry FAAC OEM and quality aftermarket hinge sets on our trucks, and most single-gate replacements are done in one visit. The usual discovery goes like this: the gate starts dragging, or it makes a grind you never heard before, or the leaf sags just enough to catch on the latch post. That sag is almost always a roller or hinge that’s given up.

Call (650) 719-7207

FAAC builds their hinge geometry around specific leaf weights and track profiles, so a hinge that feels “close enough” from a generic supplier is usually the reason the gate fails again six months later. We match the replacement to the actual FAAC model and the way that gate is used in this part of the San Fernando Valley, where heat, dust, and daily open-close cycles out here wear parts faster than most charts suggest.

Which FAAC Models This Applies To

Most FAAC sliding gates in Woodland Hills fall into two hinge camps: the S800 and 884 series, which use a paired top-hinge and lower-roller layout, and the newer C720/C721 lines that run a heavier roller carriage with a separate guide hinge. If your gate has an FAAC badge but you’re not sure of the series, look at the operator housing or the inside edge of the gate leaf. There’s usually a small data plate with the model, and on some S800 units the hinge stamp is visible on the bracket itself.

The compatibility gotcha with FAAC is real: the S800 hinge pins are metric, 20mm diameter on the post side, and a lot of “universal” hinge kits sold online use 3/4-inch pins that wallow out the bracket over time. We see this in Woodland Hills regularly on gates that were repaired once before by a generalist. OEM FAAC hinges cost more, often $85 to $140 per hinge, but they hold tolerance. A quality aftermarket set machined to FAAC spec lands around $55 to $90 per hinge. We’ll quote you both options and let you decide, because the written price is yours before we touch a bolt.

One thing worth stating: we are an independent service company, not a FAAC dealer or authorized affiliate. That matters less than you’d think, because we stock the actual FAAC part numbers and we know which series they fit without guesswork.

Signs Your FAAC Hinge & Roller Replacement Is Failing

• The gate leaf sags toward the latch side. The top hinge pin or bushing has worn enough that the gate is no longer sitting level. The fix is usually one hinge, not a whole rail.
• A grinding or scraping sound when the gate cycles. The lower roller has developed flat spots or the bearing race is full of Woodland Hills dust. Rollers with sealed bearings fail quieter; open-bearing rollers announce themselves.
• The gate shudders or hesitates partway through travel. A worn roller makes the operator work harder, which shortens the life of the motor. FAAC operators are built well, but they can’t compensate forever for a hinge that’s binding.
• Visible play when you push the gate by hand. If the gate leaf shifts more than a quarter inch at the hinge when it’s closed and latched, that’s a worn pin. It will only get worse, and it takes the track with it if you wait.
• The gate scores or rubs the track, especially in the Warner Center corridor. Commercial-grade use accelerates roller wear. If your FAAC gate sees more than 40 cycles a day, check the rollers every 9 to 12 months instead of waiting for a symptom.

Replacement Cost & What’s Included

In Woodland Hills, expect to pay between $240 and $480 for a typical FAAC hinge and roller replacement. The spread comes from a few things. A single hinge with a new roller and bushing on a standard S800 gate runs at the lower end. A full hinge set plus two heavy rollers on a C721 leaf runs toward the upper end. If the post itself has shifted in Woodland Hills clay soil, which expands and contracts with winter rain and summer drought, the job moves into post-ream and re-set territory, which adds $150 to $250.

Every quote includes the part, the labor, the removal of the old hinge or roller, and cleanup. The price is written and agreed to before we start, which is how we run every job, including FAAC hinge and roller work, across Woodland Hills. All repair work carries our written guarantee for a full year. If a hinge or roller fails inside that window, we come back and make it right at no charge. That is The Garrison Standard, and Lonnie Burke and the crew hold to it on every job, no exceptions.

DIY or Call Us?

Here’s the honest split, from someone who has fixed a lot of FAAC gates in Woodland Hills. You can safely check the symptoms: watch the gate in a full open-close cycle, look at where the leaf sits relative to the track, and push the gate by hand when it’s closed to feel for play. That tells you what’s likely wrong without tools or risk.

What you shouldn’t do is disconnect the gate from the FAAC operator and start pulling hinge pins yourself. FAAC hinges carry the entire weight of the leaf, and a gate that weighs 600 pounds or more doesn’t care about good intentions. If the hinge lets go while the leaf is off its roller, the gate can drop fast. The same goes for lowering a leaf to swap a bottom roller. We have the jack stands, the right metric hardware, and the habit of doing it without property damage. If you’re in Woodland Hills and your FAAC gate is sagging, grinding, or shuddering, call (650) 719-7207 and we’ll give you a straight answer before we send a truck.

FAQs