Wood & steel frame
Wrought iron
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Gate Parts & Welding Cost in Woodland Hills?
Gate parts and welding in Woodland Hills typically run between $150 and $450 for most component replacements, while structural welding repairs land in the $400 to $1,600 range depending on the extent of the damage. A full gate rebuild involving multiple welded sections and new hardware can reach $2,500 to $5,000 on larger driveway gates. These figures reflect what we see across Woodland Hills, Calabasas, Tarzana, and the surrounding west San Fernando Valley in 2026.
What you pay comes down to three things: the part that failed, the amount of weld time required, and whether the gate needs to come off its hinges to be worked on properly. At Carver Gate Repair Woodland Hills, every job gets a written price before work starts, so the number you’re quoted is the number you pay.
If your gate is sagging, dragging, or refusing to close, call us at (650) 719-7207 for a free estimate. We’ll tell you what’s wrong and what it costs to fix before you commit to anything.
Key Takeaways:
- Typical gate parts replacement in Woodland Hills: $150 – $450
- Structural welding repair: $400 – $1,600
- Full gate rebuild or custom fabrication: $2,500 – $5,000+
- Motor and operator failures account for roughly 40% of the gate repair calls we run in this market
- All work from Carver Gate Repair Woodland Hills carries a 365-Day Done Right Promise in writing
Gate Parts & Welding Cost Breakdown (2026)
Here’s the pricing picture for common gate parts and welding work in the Woodland Hills area. These are real numbers from the jobs we’ve run since opening this location, not national averages pulled from a database.
| Service / Part | Typical Cost Range | What’s Included |
|---|---|---|
| Hinge replacement (steel or iron) | $120 – $300 | New hardware, removal of old hinge, weld or bolt-in installation |
| Latch and lock mechanism | $90 – $250 | Part replacement, alignment, testing |
| Weld crack repair (minor, single point) | $150 – $400 | Grind-out, re-weld, spot paint/protect the repair |
| Weld crack repair (structural, multiple points) | $500 – $1,200 | Full assessment, reinforcing plate if needed, multiple weld points |
| Gate frame straightening | $350 – $900 | Alignment, jig work, weld reinforcement |
| Wheel / caster replacement (cantilever or rolling gates) | $140 – $380 | New wheel assembly, bearing check, track alignment |
| Post replacement or reset | $650 – $1,800 | Old post removal, new post set in concrete, gate re-hang |
| Gate motor replacement (swing or slide) | $850 – $2,400 | Motor, control board, remote programming, safety check |
| Custom gate fabrication (welded steel or iron) | $2,500 – $6,000+ | Design, material, fabrication, finish, installation |
| Security welds on broken pickets/rails | $100 – $350 per section | Weld repair on pickets or rails, rust treatment |
These ranges assume a standard residential gate, which is what most homes in Woodland Hills have. Driveway gates along Mulholland Drive and in the hillside neighborhoods south of Ventura Boulevard tend to run larger and heavier, which adds material and labor cost. Gates in the flatland neighborhoods north of the 101, like Walnut Acres and parts of Canoga Park bordering Woodland Hills, are often smaller and lighter, so they land at the lower end of these ranges.
What Moves the Price Up or Down
Steel thickness is the biggest swing factor in any welding job. A thin-walled aluminum gate is a completely different repair from a solid wrought iron gate that’s been on the property since the 1970s. Aluminum requires a different weld process or mechanical fastening, and that changes the labor time. Wrought iron and heavy steel drink wire and rod, and they often need pre-heating to avoid stress cracks in the repair zone.
Access is the second factor. In Woodland Hills, a large share of driveway gates sit on sloped lots. If we have to set up on an incline, work around retaining walls, or remove a gate panel to get it to a flat work surface, that’s additional labor and it shows up in the price. Flat, straight driveway access keeps the number lower.
Finish work matters too. A bare weld left unpainted will rust within a season or two in this climate, especially with the morning marine layer that rolls through the valley from the coast. If you want the repair primed and painted to match the rest of the gate, or powder-coated if the panel can be transported, that adds $75 to $250 depending on the size of the repair area.
For a deeper walkthrough of the specific parts and welding services we run in this market, see our Gate Parts & Welding in Woodland Hills page.
What Affects Gate Parts & Welding Pricing in Woodland Hills
Beyond the basic part cost, six local factors consistently shape the final number on a gate parts or welding invoice in this area.
- Gate material and steel thickness: Wrought iron and solid steel gates from the 1960s and 1970s (common in the ranch-style homes south of Ventura Boulevard) are heavier and more labor-intensive to weld than modern aluminum or thin-wall steel gates. Material determines weld method, prep time, and consumables used.
- Slope and access: Many Woodland Hills properties sit on graded lots, especially in the neighborhoods climbing toward the Santa Monica Mountains. Working on a sloped driveway adds setup time, and some hill-gate repairs require the panel to be removed and worked on flat ground.
- Corrosion and rust level: The marine layer that reaches Woodland Hills in the mornings accelerates rust on unprotected steel. Severe rust means grinding out more material, sometimes fabricating and welding in patch plates, and applying rust-inhibitive primer. That’s more shop time and a higher bill than a clean, surface-level crack.
- Gate design complexity: Ornamental gates with scrollwork, spears, and decorative pickets take longer to repair than a simple flat-panel gate because each welded intersection is a potential failure point that must be checked. Curved or radius gates also require more careful jigging to keep the geometry true.
- Post and footing condition: A sagging gate often points back to a failed gate post, not the gate itself. If the post has shifted or the concrete footing is cracked, the fix is a post reset, not just a hinge swap. That’s the difference between a $250 hinge job and a $1,200 post job.
- Motor and automation components: When a gate won’t open, homeowners sometimes think welding is needed when the real issue is a failed limit switch or control board. If we diagnose an electrical problem, the parts cost shifts to the operator side: control boards for LiftMaster, FAAC, and BFT systems run from $250 to $700, installed.
Common Gate Parts That Fail in Woodland Hills
Certain parts show up in our work orders repeatedly in this market. Knowing what typically fails helps you understand what you’re paying for when you see that line item on a written estimate.
Hinges and Barrel Bolts
Gate hinges in Woodland Hills take a beating from the wind that funnels through the valley, especially on wider driveway gates that act like a sail. Worn barrel hinges let the gate drop, which puts strain on the latch side and drags the leaf across the driveway. Hinge replacement with weld-in or bolt-in hardware runs $120 to $300 for a standard residential gate. If the hinge welds have pulled out of the gate frame, the repair shifts into weld work, and the cost moves to $350 to $600.
Latch and Lock Systems
Gate latches fail from repeated slamming and misalignment. The fix is usually a new spring-loaded latch, a heavier duty lock housing, or a magnetic catch for lighter aluminum gates. Parts and labor range from $90 to $250. If the gate frame itself is out of square because of a broken weld, the latch replacement alone won’t hold, and we’ll flag that before we do the work.
Weld Joints and Frame Corners
The corners of a steel gate frame are where cracks appear first, followed by the points where pickets meet the top rail. In Woodland Hills, the temperature swings between valley heat and overnight cooling create expansion and contraction cycles that work on these joints over the years. A single crack welded, ground, and painted runs $150 to $400. Multiple cracks with reinforcing plates can run $600 to $1,200 because the gate often comes off its posts and gets laid flat for proper work.
Gate Motors and Operators
We service nine gate-motor brands at Carver Gate Repair Woodland Hills: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. Motor replacement runs $850 to $2,400 depending on the brand and the duty cycle the gate demands. A failed control board, which often presents as “the gate is dead,” is usually a $350 to $700 repair on its own. We carry boards and parts for all nine brands on our trucks, so the diagnostic and repair usually happen in one visit.
Welding Repair: What Homeowners Should Know
Welding is a skilled trade, and it’s also a safety-critical one. A bad weld on a 400-pound gate can fail without warning and cause serious injury or property damage. The work involves high heat, electrical current, and in some cases, gas tanks. If you’re researching how to fix a cracked gate, know this: proper welding requires equipment, training, and a work surface that won’t start a fire in your driveway. The sagebrush and dry brush on hillside lots in Woodland Hills don’t mix with weld sparks. A trained professional with flame-resistant mats and a fire watch protocol is the only safe option.
Our weld repairs follow a consistent process at this location. We grind out the crack to clean metal, bevel the edges for penetration, weld in short passes to avoid warping the gate frame, and then protect the repair with primer and paint. On structural welds, we add a gusset or backing plate where needed so the joint is stronger than the original. Every weld repair is covered by the 365-Day Done Right Promise, in writing. If the weld fails within a year, we return and fix it at no charge.
Should You Repair or Replace Your Gate?
This is the question we hear most often from homeowners during a quote visit. The answer depends on three numbers: the repair cost, the gate’s age and material condition, and what a replacement would cost.
As a rule, if the gate structure is sound and the repair bill is under 40% of replacement cost, repair is the right call. Woodland Hills replacement costs for a standard steel driveway gate start around $2,500 for a simple flat-panel gate and climb past $6,000 for ornamental iron. A $600 weld repair on a gate that would cost $5,000 to replace is money well spent.
If the gate has extensive rust, the posts are shifting, the frame is racked, and multiple weld points have failed, replacement starts to make financial sense. We’ll lay out the numbers on both sides with a written quote and let you decide. We don’t push replacement when repair will hold.
How to Save on Gate Parts & Welding
Saving money on gate work isn’t about finding the lowest bidder. In this trade, low bids often mean welds that get covered in paint before you can see the porosity underneath. Saving money means catching problems early, matching the right part to the gate, and not paying for rework.
- Check your gate monthly: Walk the gate and look at the hinge points, the latch, and the bottom rail. Small cracks caught early are $150 repairs. The same crack left for a year can rack the gate and turn into a $1,000 structural job.
- Keep the track and wheels clean: If you have a rolling or cantilever gate, debris in the track is the leading cause of wheel and motor strain. Blow the track out with a leaf blower or hose it down monthly, especially after the Santa Ana winds drop debris across driveways in the valley.
- Don’t force a stuck gate: If the gate doesn’t move, don’t put the car against it or shove it by hand. You’ll bend the frame or strip the operator gears, and you’ll turn a small repair into a big one. Call us instead.
- Get a written price before work starts: That’s standard practice at Carver Gate Repair Woodland Hills. Written prices mean you know exactly what the repair costs before we pick up a weld torch. No surprises, no moving numbers at the door.
- Use rust-inhibitive primer on scratches: If you notice a scratch through the paint on your gate, hit it with a rattle can of primer. The coastal air that reaches Woodland Hills in the mornings will turn bare steel into rust quickly, and rust drives repair costs up.
Call (650) 719-7207 for a free estimate. We’ll give you a straight answer on what the gate needs and what it costs before any work begins.
How the Carver Gate Repair Process Works
Our operation in Woodland Hills runs on The Garrison Standard, which is the set of operating rules every location in the Garrison Partners family has followed since 2008. Here’s what that looks like for you, step by step.
- Call us at (650) 719-7207: A live person answers, 24 hours a day, every day of the year. No voicemail boxes, no call-back queues, no “we’ll call you Monday.”
- We schedule a visit: You’ll get a real arrival window, and the technician shows up in a uniform with identification. You’ll know exactly who you’re letting through the gate.
- Diagnosis and written price: We inspect the gate, identify the failed part or the weld problem, and hand you a written price before picking up a tool. The number on that page is the number you pay.
- Repair or welding work: The technician completes the work on-site in most cases, using the parts and equipment on the truck. For larger fabrication jobs, we handle transport and shop work.
- Written guarantee: Every repair carries the 365-Day Done Right Promise in writing. If the repair fails within one year, we come back and make it right at no charge. Second visit is free, no questions, no argument.
This is the process home page visitors read about before they call, and it’s the same process we follow on every job in Woodland Hills.
FAQs – Gate Parts & Welding Cost
How much does it cost to weld a broken gate in Woodland Hills?
Welding a broken gate in Woodland Hills costs $150 to $1,200, depending on whether it’s a single crack at a hinge point ($150 – $400) or structural damage at multiple welded joints ($500 – $1,200). The cost includes grinding out the crack, welding, grinding the weld smooth, and protecting the repair so it doesn’t rust. Call (650) 719-7207 for an exact quote on your gate, estimates are free.
Is it cheaper to repair or replace a gate?
Repair is cheaper when the repair bill stays under 40% of replacement cost. In Woodland Hills, a typical gate replacement runs $2,500 to $6,000, so a $400 weld repair is almost always the right call on a gate that’s structurally sound. We’ll give you written numbers for both repair and replacement before you decide.
How much does a gate motor or operator cost in Woodland Hills?
A new gate motor or operator in Woodland Hills runs $850 to $2,400 installed, depending on the brand and the size of the gate. We service LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule systems, and our trucks carry parts for all nine brands. If the motor is fine and the issue is a control board, that repair is typically $350 to $700.
Can you fix my gate the same day?
In most cases, yes. Hinge replacements, latch repairs, single-point weld fixes, and motor swaps usually happen the same day because our technicians carry the common parts and welding gear on the truck. For larger structural welding jobs that require removing the gate and working it in the shop, schedule the visit and we’ll give you a clear completion date with your written price.
What does a gate wheel or caster replacement cost?
Replacing a gate wheel or caster assembly in Woodland Hills runs $140 to $380, including the new wheel assembly, bearing check, and track alignment. If the track itself is damaged and needs repair or replacement, the total can push toward $600 to $900 depending on the length of track involved.
Do you give free estimates for gate parts and welding?
Yes. Every estimate at Carver Gate Repair Woodland Hills is free, and every estimate is delivered as a written price before any work begins. Call (650) 719-7207 and we’ll set a visit time that works for you.
Call Carver Gate Repair Woodland Hills for Gate Parts & Welding
When a gate fails, it stops being a convenience and starts being a problem: cars stuck in or out, a security opening on the property, and a repair that gets worse every day it waits. Our crew in Woodland Hills handles gate parts replacement, structural welding, and motor repair with one standard: a written price, a uniformed technician, and a guarantee that lasts a full year.
Call (650) 719-7207 now for a free estimate. A live person answers, 24/7. We’ll get your gate working right the first time, and we’ll put the guarantee in writing.
Written by Lonnie Burke, Owner at Carver Gate Repair Woodland Hills, serving Woodland Hills since 2008.
Pricing reflects the Woodland Hills market as of 2026. Carver Gate Repair Woodland Hills offers free estimates – call (650) 719-7207.
What Our Customers Say
"Added a battery backup so the gate works during a power outage. Easy to use."
- Mitch L."Good repair on a motor board. Waited a few days on the part, but they stayed in contact."
- Shelby T."Photo eyes cleaned and aligned. Gate stops for the dog like it should."
- Henry B.